Wa5320-C&D WiFi Router high-speed Ap Indoor Wireless Access Point Modem

• Work Mode: AP
• WiFi Antenna Type: Built-in
• Transmission Rate: >200Mbps
• Model NO.: EWP-WA5320-C-FIT
• Certification: FCC
• Transport Package: Carton
• Specification: 170mm x 170mm x 35mm
• Origin: China

Product Description

WA5320-C&D series wireless products are a new generation of ultra-gigabit high-speed wireless access equipment (hereinafter referred to as AP) based on 2-Streams 11ac MIMO technology independently developed by H3C Technology Co., Ltd. (H3C), supporting the latest 802.11ac Wave2 technology standards , Among them, the WA5320-C series wireless product uplink adopts dual Ethernet interface design, breaking through the limitation of Gigabit Ethernet interface, making wireless multimedia application a reality, and adopts dual Ethernet configuration, dual interface PoE power supply.

Enables smart gigabit cloud access and better wireless network TCO

WA5320-C series AP complies with the new 802.11ac Wave2 protocol standard and can provide a 2-Streams wireless transmission rate of 867Mbps and an access capability of 1267Mbps. It provides higher-performance mobile cloud access services and helps users achieve better wireless network TCO (Total Cost of Ownership).

High reliability dual network port design

H3C WA5320-C series equipment is designed with dual network ports and dual uplink Gigabit Ethernet ports, which not only solves the problem of interface data backup, but also can be used for networks that need to be isolated from internal and external networks. Provide flexible networking methods. The dual Ethernet ports of WA5320-C and WA5320-C-EI can accept PoE power supply to realize the backup of PoE power supply.
 

Realize multi-terminal simultaneous communication, break through the disadvantages of traditional wireless competition

H3C WA5320-C/D series APs support MU-MIMO technology. MU-MIMO is one of the most important features of 802.11ac Wave 2. Through MU-MIMO technology, APs can send data to multiple terminals at the same time, namely WA5320-C The series can send data information for multiple terminals at the same time, breaking through the traditional wireless network serial communication mechanism, the utilization rate of wireless spectrum resources has been doubled, the number of effective access users has been greatly improved, and the deployment overhead of wireless networks has been effectively reduced. Improve user experience in high-density user scenarios.
 

Green and low carbon design

Provides 802.3af compatible power supply mode (excluding expansion modules), 802.3af compatible mode is automatically detected without user intervention.
WA5320-C/D series AP adopts professional green and low-carbon design, supports dynamic MIMO power saving mode (DMPS) and enhanced automatic power saving transmission (E-APSD), intelligently identifies the actual performance requirements of the terminal, rationally allocates the terminal sleep queue, dynamic Adjust the MIMO working mode.
The WA5320-C/D series AP supports the Green AP mode, which realizes single-antenna standby, and achieves low carbon and environmental protection to the greatest extent possible.
WA5320-C/D series AP adopts innovative packet-by-packet power control (PPC) technology to dynamically adjust the direct bidirectional power between AP devices and clients on the premise of ensuring successful packet transmission, so as to reduce device energy consumption and extend the power consumption. The role of mobile terminal standby time.
 

Provide local forwarding function

When the WA5320-C/D series APs are forwarded through the WAN, the wireless access device is deployed in the branch office, and the wireless controller is deployed in the headquarters. All user data is sent by the wireless access device to the wireless controller, and then by the wireless controller. Centralized forwarding. WA5320-C/D series APs can directly convert data packets into wired format packets on wireless access devices, so that data packets are forwarded locally without passing through the wireless controller, which greatly saves wired bandwidth.
 

Support IPv4/IPv6 dual protocol stack (Native IPv6)

WA5320-C/D series APs fully support IPv6 features, and the device implements IPv4/IPv6 dual protocol stacks. Regardless of whether the original wired network is IPv4 or IPv6, it can automatically register with the H3C WX series controller to provide WLAN services without becoming an information island in the network.
 

Provide EAD wireless access

The End User Admission Domination (EAD) solution starts from the perspective of controlling the secure access of user terminals to the network, integrates network access control and terminal security products, and enforces enterprise security policies for user terminals accessing the network. Linked with the security policy server, unqualified wireless clients that are infected with viruses or have system vulnerabilities can be processed in various ways, such as offline, isolation, reminder or monitoring. Only wireless clients are allowed to comply with the corresponding security policies. Access the network normally, thereby improving the overall security of the wireless network.
 

Support remote probe analysis

WA5320-C/D series APs support as a Sensor device for remote probe analysis, which can monitor and capture Wi-Fi packets in the coverage area and mirror them to the local analysis device in real time for network administrators to troubleshoot and optimize analysis. The remote probe analysis function can perform non-convergence mirroring for the working channel, or poll and sample all channels, flexibly meeting the wireless network monitoring operation and maintenance requirements.
 

Built-in RF Optimization Engine (ROE)

The WA5320-C/D series APs have a built-in RF Optimizing Engine. Through feature- and protocol-based RF optimization, the application acceleration capability and quality assurance effect in scenarios such as high-density access and streaming media transmission in wireless deployments can be effectively improved. These include: multi-user fair scheduling, hybrid access fairness, filtering interference, better rate, spectrum navigation, multicast enhancement (IPv4/IPv6), packet-by-packet power control, and intelligent bandwidth guarantee.
 

Support intelligent load balancing

WA5320-C/D series AP supports complex balancing method according to the number of access users and traffic. When the wireless controller finds that the load of the wireless access device exceeds the set threshold, the wireless controller will respond to the newly connected user. Automatically calculates whether there are any lightly loaded wireless access devices around the user that can be accessed by the user. If so, the user's association request will be rejected, and the user will switch to other lightly loaded wireless access devices. Wireless users are not in the overlapping coverage area. Traditional load balancing methods often lead to failure to connect to the network, resulting in false balancing. H3C's innovative support for intelligent load balancing technology ensures that the load balancing function is only activated for wireless users in overlapping coverage areas, effectively avoiding the occurrence of false balancing, thus maximizing the wireless network capacity.
 

Support Chinese SSID

WA5320-C/D series APs support the use of Chinese SSIDs, which can specify SSIDs with a maximum of 16 Chinese characters, and can also use mixed Chinese and English SSIDs, providing greater convenience for domestic users.
 

Fully support intelligent wired and wireless integrated management

All H3C series wireless products can realize WSM-based wired and wireless integrated management through open network management protocols.
WSM is a wireless operation management component developed by H3C on the basis of the next-generation business software platform iMC (intelligence Management Center/Intelligent Management Center). The scalability can meet the evolving needs of customer network management. The Web-based management system provides a simple and friendly management platform for wireless business managers. In cooperation with the iMC intelligent management platform and other components, it can also realize the panel management, fault management, performance monitoring, software version management, configuration file management, access user management and other functions of wireless devices, and can unify other devices in the network. management, and truly realize intelligent wired and wireless integrated management.

The WA5320- C wireless access point is only suitable for indoor installation and supports the following two installation methods:
·     Wall-mounted installation
·     Ceiling installation

1. Wall-mounted installation

When the device is wall-mounted, you need to select the two mounting holes on the mounting kit as shown in the figure below.
Figure 3-1 Schematic diagram of wall mounting (ceiling) mounting holes (unit: mm )

 Wall (ceiling) mounting kits are divided into AP mounting and wall (ceiling) mounting, AP mounting is fixed to AP, and wall (ceiling) mounting is fixed to ceiling or wall.

Figure 3-2 Structure of AP mounts and wall-mounted (ceiling) mounts

1: AP mount	2: AP mount positioning protrusion
3: Wall (ceiling) mounts	4: Wall (ceiling) mounting holes

 

 

note:

Please use M4 × 7mm pan head screws to fix the AP mounting hardware to the AP to avoid equipment damage caused by incorrect use of screws.

 
The installation steps of the wall-mounted installation method are as follows:
(1) Align the positioning protrusions of the AP mounting piece with the positioning holes on the back of the AP, and tighten the M4 x 7mm pan head screws to fix the AP mounting piece to the AP.
Figure 3-3 Fixing the AP mount to the AP

 
(2) Attach the wall-mounted (ceiling) mounting piece to the wall, and mark the positions of the holes where the screws need to be installed.
Figure 3-4 Marking the location of the mounting screws

 
(3) Use an impact drill to drill two holes with a diameter of 6.0 mm at the marked places. The drilled holes correspond to the mounting holes on the mounting kit, as shown in the figure below.
Figure 3-5 Drilling holes in the wall

(4) Insert the expansion coil into the drilled hole on the wall, and tap one end of the expansion coil with a rubber hammer until all the expansion coil is knocked into the wall, as shown in the figure below.
Figure 3-6 Fixing the expansion coil

 
(5) Align the mounting holes of the wall-mounted (ceiling) mounting parts with the expansion screw holes, pass the screws through the corresponding mounting holes, adjust the position of the mounting kit, and tighten the screws, as shown in the figure below.
Figure 3-7 Fixing the wall-mounted (ceiling) mount to the wall

 
(6) As shown in Figure 3-8, align the AP with the wall-mounted (ceiling) mounting bracket, and then rotate it clockwise to the vertical position. When you hear a "pop", the AP has been locked and the installation is complete. .
Figure 3-8 Installing the AP on the wall

 

2. Ceiling installation

 

·The      ceiling installation method requires that the thickness of the ceiling must be less than 18mm, and the ceiling can bear at least 5kg of weight.
If it is a material with weak strength such as      gypsum ceiling, this installation method is not recommended. If this installation method must be adopted due to environmental restrictions, please add a layer of better strength plate under the nut to ensure that the equipment is firmly installed .

 
The installation steps of the ceiling installation method are as follows:
(1) Align the positioning protrusions of the AP mounting parts with the positioning holes on the back of the AP, and tighten the M4 × 7mm pan head screws to fix the AP mounting parts to the AP, as shown in Figure 3-3.
(2) Attach the wall-mounted (ceiling) mounting piece to the ceiling, mark the position of the hole where the screw needs to be installed, and then drill two holes with a diameter of 5.0mm, and the drilled holes correspond to the mounting holes on the mounting kit .
Figure 3-9 Drilling holes in the ceiling

 
(3) Pass the pan head screws through the mounting holes on the wall (ceiling) mounting and the drilling holes on the ceiling, and use nuts and washers to tighten the bolts at the other end of the ceiling to secure the wall (ceiling) mounting on the ceiling.
Figure 3-10 Fixing the installation kit to the ceiling

 
(4) Align the AP with the wall-mounted (ceiling) mounting bracket, and then rotate it clockwise to the vertical position. When you hear a "pop", it means that the AP has been locked and the installation is complete. For details, please refer to 1. (6) of the wall-mounted installation method .
Figure 3-11 1Installing the AP on the ceiling



 

Hardware Specifications

 

Attributes	WA5320-C	WA5320-C-EI	WA5320-C-IOT	WA5320-D
weight	0.50kg
Dimensions (excluding antenna interface and accessories)	170mm x 170mm x 35mm
Gigabit Ethernet port	2		2 (one of which supports IoT expansion)	1
IoT interface	none		1 IOT interface can support up to 10 IoT modules to expand	none
powered by	Support 802.3af/802.3at and local power supply
Console port	1
USB port	1
Built-in antenna	Built-in antenna system (working frequency band: 2.4G and 5G, maximum gain up to 3dBi)
Working frequency	802.11ac/n/a : 5.725GHz-5.850GHz ; 5.15~5.35GHz (China) 802.11b/g/n : 2.4GHz-2.483GHz (China)
Modulation technology	OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps DSSS: DBPSK@1Mbps, DQPSK@2Mbps, [email protected]/11Mbps MIMO-OFDM (11n): MCS 0-31 MIMO-OFDM (11ac): MCS 0-39
Modulation	11b:DSS:[email protected]/11Mbps,DQPSK@2Mbps,DBPSK@1Mbps 11a/g:OFDM:64QAM@48/54Mbps,16QAM@24Mbps,QPSK@12/18Mbps,BPSK@6/9Mbps 11n:MIMO-OFDM:BPSK,QPSK,16QAM,64QAM 11ac:MIMO-OFDM:BPSK,QPSK,16QAM,64QAM,256QAM
Transmit power (single channel)	20dBm	23dBm	20dBm
Adjustable power granularity	1dBm
reset/restore factory configuration	support
Status Indicator	Rich interface indicators, providing orange, green, blue different working status display.
Operating temperature/Storage temperature	-10ºC~55ºC/-40ºC~70ºC
Working Humidity/Storage Humidity	5%~95% (non-condensing)
Protection class	IP41
Machine power consumption	<12.95W (excluding expansion modules)	<20W	<25W	<12.95W (excluding expansion modules)
safety regulations	GB4943, UL/CSA 60950-1, EN/IEC 60950-1, EN/IEC 60950-22
EMC	GB9254, EN301 489, EN55022, RSS-210
RF Certification	EN 300 328, EN 301 893
Health	FCC Bulletin OET-65C, EN 50385, IC Safety Code 6
MTBF	>250000H

 

Software Specifications

Attributes		WA5320-C / WA5320-C-EI / WA5320-C-IOT	WA5320-D
Product Positioning		Indoor installation type dual frequency
11ac support	Streams	2
	Working frequency	5GHz
	80MHz bundle	support
	MU-MIMO	support
	867Mbps(PHY)	support
	A-MPDU	support
	A-MSDU	support
	Maximum Similarity Demodulation (MLD)	support
	Maximum Combined Ratio Receive (MRC)	support
	Space Time Block Code (STBC)	support
	Low Density Parity Check Coding (LDPC)	support
11n support	Streams	2+2	2(5GHz)+1(2.4GHz)
	Working frequency	2.4GHz and 5GHz
	40MHz bundle	Support (2.4GHz not recommended)
	400Mbps(PHY)	support
	A-MPDU	support
	Maximum Similarity Demodulation (MLD)	support
	Switching Beamforming (TxBF)	support
	Maximum Combined Ratio Receive (MRC)	support
	Space Time Block Code (STBC)	support
	Low Density Parity Check Coding (LDPC)	support
WLAN Basics	Maximum number of access users per radio	256 (the actual number of users varies due to factors such as the application environment)
	Virtual AP (recommended to set at most 5 per radio in practical applications)	32
	open system/shared key authentication	support
	Broadcast Probe request response control	support
	WPA, WPA2, Pre-RSNA User Hybrid Access	support
	RTS/CTS	support
	CTS-to-self	support
	Hide SSID	support
WLAN extension	STA related	Supports abnormal STA offline detection, STA aging, STA-based statistics and status query, etc.
	Access user limit	support
	Link Integrity Check	support
	Repeater mode	support
security strategy	encryption	Support 64/128-bit WEP, dynamic WEP, TKIP, CCMP (11n recommended) encryption
		Supports multiple key update trigger conditions to dynamically update unicast/broadcast keys
	802.11i	support
	Certification	Support 802.1X authentication, MAC address authentication, PSK authentication, Portal authentication, etc. (H3C WX series wireless controllers may be required depending on the application)
	User isolation	support: 1. Layer 2 isolation of wireless users 2. SSID-based wireless user isolation
	Forwarding security	Support packet filtering, MAC address filtering, broadcast storm suppression, etc.
	Wireless Endpoint Admission	Support/Wireless EAD
	SSID and VLAN binding	support
	Intelligent Wireless Service Awareness (wIAA)	support
	wIDS/wIPS	support
	Management Frame Protection (802.11w)	support
	Real Time Spectrum Guard (RTSG)	support
AAA	Radius Client	support
	Authentication server multi-domain configuration	support
	Backup Authentication Server	support
Layer 2 and Layer 3 functions	IP address settings	Support: static IP address or DHCP to obtain IP address (optional option 60)
	Native IPv6	support
	IPv6 Portal	support
	IPv6 SAVI	support
	ACL	Support (IPv4/IPv6)
	local forwarding	Support: local forwarding based on SSID+VLAN
	multicast	IGMP Snooping/MLD Snooping
service quality	802.11e	Support WMM
	priority	Support Ethernet port 802.1p identification and marking
		Support wireless priority to wired priority mapping
	QoS Policy Mapping	Support different SSID/VLAN mapping with different QoS policies
	Support L2~L4 packet filtering and flow classification functions	support
	CAR	support
	User Bandwidth Management	Available bandwidth can be allocated per STA, or all STAs can share the total bandwidth by SSID
	load balancing	Support: based on traffic, user, frequency band (dual frequency support)
	Spectrum Navigation	support
	Multicast optimization	Support: Multicast to Unicast (IPv4/IPv6)
	CAC (Call Admission Control)	Support: based on number of users and based on channel utilization
	SVP Phone	support
green technology	Packet-by-Package Power Control (PPC)	support
	Green AP mode	support
	Dynamic MIMO power saving	support
	Enhanced Automatic Power Save Delivery (E-APSD)	support
	WMM Power Save	support
Management and maintenance	network management	SNMP V1/V2c/V3, Trap, HTTP(S), SSH, Telnet, FTP/TFTP
	Manage SSIDs	support
	log function	SYSLOG
	Remote Probe Analysis	support

Solutions we can offer

 

We focus on the IDC data center field, have professional enterprise-level products, and provide complete planning and design solutions.

Main Application Scenarios:

Only applies to servers.

 

 

Packaging & Shipping

Delivery time : 15-20 working days after payment receipt confirmed (based on actual quantity).

Original packaging to ensure product quality and safety.

Professional goods shipping forwarder.

After Sales Service

We guarantee that all products are original and authentic. All support after-sales inspection. Regarding xFusion server, we can provide remote technical services and troubleshooting.
In addition to new retail products. Others have used NEW BULK. We provide a complete test report. Please rest assured to buy. The stock is huge. Many products are not released in time. If you need more product quotations. You can email to contact us at any time. 

 

FAQ

Q1: How can I believe that your product is of good quality?
A1: We guarantee that all products are original products.We provide a complete test report.

Q2: When can I get a quote?
A2: We will usually quote you within 24 hours after receiving your inquiry. If you really want to get a quotation and more other questions, you can contact us via trademessage or email.

Q3: Why choose you?
Q3: As an Audited Supplier,we have a good reputation on our customers,because of the good quality,suitable price and good service.

Q4: What is your payment?
A4: T/T wire bank transfer.